Manico 3 prong trolling motor plug6/27/2023 Plus, connecting the wires can lead to a high generation of energy supporting up to 36V. These plugs can hold multiple wires, allowing a user to attach more than one battery up to 3 batteries at a time. Universal Design – Another type of division of power is universal design.Make sure that they aren’t capable of attaching multiple batteries. It can be used for light voltage batteries, further preventing heating issues. Single Voltage Design – Using a single voltage design means it will support a 12V trolling motor battery.This further tends to be easy maintenance with no complicated wiring.īased on the power division, we can broadly categorize the motor plus into two categories: The plugs are lightweight connectors and will preferably be easily replaced.But choosing a motor plug will end this too. Assembly and disassembling of wires over and over could be exhausting.As the connection is established safe and secure, you will rarely find any wire heat issues or sparkling issues of open wires.Issues such as loosening of the connections between trolling motor and the motor plug shall never be encountered. It will provide a long-lasting and secure connection with the trolling motor.Hence it is essential to keep the key considerations a good quality plug will tend to provide you. M-G Electronics 4-pin Trolling Receptacle Assy eBay M-G Electronics 4-pin Trolling Receptacle Assy Condition: New Bulk savings: Buy 1 14.95/ea Buy 2 13.46/ea Buy 3 12.71/ea 4 or more for 11.96/ea Quantity: More than 10 available / 151 sold Price: US 14. This will allow you to remove the wiring that’s closest to the battery quickly and easily.A suitable trolling motor plug can prove to have various advantages. However, if you have a transom mount motor, we recommend that you consider a quick-connect plug for trolling motors that will attach to the terminals on the circuit breaker and the battery. For example, if you wanted to attach a quick-disconnect wire near the trolling motor or in-line with the trolling wire plug, you can find a quick-connect plug. Note 2: If the thought of drilling a hole into your boat scares the living day lights out of you, don’t worry! There are a few other options that you could choose instead. Unfortunately, there isn’t a universal plug design and most trolling motor plugs and receptacles aren’t compatible with one another. If you cannot contact the manufacturer for one reason or another, you could always remove the old receptacle and use this guide to install a new one. Note: It’s important to note that if your boat already has a plug receptacle, you’ll want to check with the boat dealer (if you’re buying brand new) or the manufacturer of the receptacle already on your boat (if you’ve bought a used boat) to find the matching plug for the already-installed receptacle. When you’ve attached the battery leads to the batteries, you will then want to plug the trolling motor plug into the receptacle. Place the receptacle back in the hole you drilled and use the 7/64-inch screws to hold the receptacle in place. Remove ½-inch of the wire coating on the trolling motor wire that’ll plug into the back of the new receptacle and both the negative and positive power leads from the trolling motor itself.Ĭonnect the trolling motor’s power leads into the male end (the plug) and the battery leads to the female end (the receptacle). You’ll then want to use the 7/64-inch drill bit to make these holes. Put the receptacle in the newly drilled hole and use the small holes on the side of the receptacle to mark where the screws will go to hold the receptacle in place. 1 1/8-inch is standard size for trolling motor plugs, but you’ll want to check out the instructions for your particular plug just in case the measurements are different than what we state here. We recommend choosing a vertical surface because water is less likely to get inside the plug or it’s receptacle.ĭrill a 1 1/8-inch hole in the surface for the receptacle. Follow these steps:įind a surface on the boat where the structure is strong and out of reach of a lot of water. With all of your tools within reach, now you’re ready to install the plug and the receptacle on your trolling motor.
0 Comments
Leave a Reply. |